Effect of chemical parameters on pyrene degradation in soil in a pulsed discharge plasma system

Degradation of pyrene in soil in a net-to-net pulsed discharge plasma (PDP) system was reviewed. Effect of main chemical parameters, including air flow rate, pyrene concentration, initial pH and soil moisture content on pyrene degradation was examined. The obtained results show that 87.9% of pyrene could be removed under the condition of 60 min reaction; increasing of air flow rate within 1 L min⁻¹ was favorable for degradation; pyrene removal was decreased with the increase of initial pyrene concentration; oxidation of pyrene was more evident in acidic soil; enhancement of soil moisture content has no benefit on pyrene degradation.     

Elongating the area of plasma/fluid interaction of surface nanosecond pulsed discharges

Plasma-assisted flow control is of high industrial interest, but practical applications at full scale require a large surface of interaction. Nanosecond pulsed Dielectric Barrier Discharge (DBD) have demonstrated promising results of flow control, but their interacting region is limited to only a few cm². In this paper, the conditions to extend a surface nanosecond DBD are documented. It is shown that a sliding discharge regime can fully fill an inter-electrode distance of 40 mm. This discharge regime promotes the formation of two hemispheric pressure waves originating from both air-exposed electrodes while an horizontal region of pressure gradient is also observed.     

Micromachining of circular ring microstructure by femtosecond laser pulses

In this paper, integration of interference phenomenon into femtosecond laser micromachining was reported as the femtosecond laser pulses were reshaped spatially to perform ablation. The generation of circular interference pattern was demonstrated by overlapping infrared femtosecond laser pulses. The interference pattern was subsequently focused on a copper substrate to ablate microstructures of concentric circular rings. The present technique is expected to open up new applications in the areas of rapid fabrication of micro-Fresnel lenses, hybrid microlenses and lens arrays.     

等离子体电极棚电光开关实验研究

 设计建造了以辉光放电形成的等离子体作电极，通光口径为80mm×80mm的普克尔盒实验，实验检测了它的开关性能。阐述了普克尔盒的结构，辉光放电等离子体电极的形成，开关驱动脉冲的产生及输出特性，电光开关的开关效率和开关速度的检测方法，给出了典型的实验结果。     

Spectral and temporal characteristics of metallic nanoparticles produced by femtosecond laser pulses

We study the time of flight optical emission from titanium and tungsten nanosized particles, generated through femtosecond laser-matter interaction in vacuum, in the wavelength spectral range from 300 to 900 nm. Typical spectra consist of broadband structureless signals similar to black body emission from a macroscopic object. Nanoparticles temperature, deduced from their emission spectra, decreases drastically as a function of their time of arrival at a given distance from the target. This behaviour is seen to be independent of individual particle velocities.     

电子回旋共振放电的电离特性PIC/MCC模拟(Ⅰ)——物理模型与理论方法

采用粒子模拟与蒙特卡罗相结合(PIC/MCC)的方法对电子回旋共振(ECR)放电中的电离过程进行了模拟，其中带电粒子与微波的相互作用由PIC方法的电磁模型描述，粒子间的碰撞过程由MCC方法描述.考虑的碰撞类型有电子与中性粒子的弹性、激发、电离碰撞，离子与中性粒子的弹性、电荷交换碰撞，碰撞截面均依赖于能量而变化.阐述了理论分析的过程，为数值模拟ECR放电奠定了基础. 关键词： 电子回旋共振放电 粒子模拟 蒙特卡罗 电离     

Polytetrafluoroethylene and metal structure convective-flow CO laser

A convective flow CO laser composed of polytetrafluoroethylene discharge tubes, nickel–chromium steel components, a cupric heat exchanger and other components is described. Operating in liquid nitrogen condition, output power of 60 W has been obtained from a non-selective cavity.     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

硅光电二极管激光损伤阈值随激光脉宽的变化

 对飞秒激光辐照下硅光电二极管损伤阈值进行了实验测量，对从1s到60fs不同脉宽激光辐照下硅光电二极管损伤阈值进行了讨论。实验数据表明，在1s到10ns脉宽范围内损伤所需能量密度近似而非严格地与脉宽的平方根成正比。信号分析表明硅光电二极管的损伤主要由热效应造成，而60fs激光辐照下的损伤阈值为0.1J/cm2，明显偏离普通温度分布预言的趋势。     

Analysis of semiconducting materials by high-resolution radiofrequency glow discharge mass spectrometry

The analytical capabilities of a high-resolution mass spectrometer in combination with a 13.56 MHz glow discharge ion source for the analysis of semiconducting materials (silicon carbide and gallium arsenide) were studied. It was shown that single positively charged ions of sample material have about 10 eV higher average energy than the ions of the discharge and residual gas. Therefore effective energy separation of the ions of analyte from the ions of the discharge and residual gas was achieved by adjusting the ion transfer optics (breadth and position of energy slit), which improves the analytical capabilities of the developed method.Some analytical applications are presented to illustrate the performance of r.f. GDMS for the bulk analysis of semiconducting materials. The results of the trace element analysis of gallium arsenide and silicon carbide samples are compared with data of independent methods (LIMS, ICP-AES, SIMS).Dedicated to Professor Dr. rer. nat. Dr. h.c. Hubertus Nickel on the occasion of his 65th birthdayOn leave from the Institute of Inorganic Chemistry, 630090 Novosibirsk, Russia